Wearable Solution


Contents

Introduction


The Telink Wearable solution is based on the Wearable EVK built on Telink’s B91 platform. A 454*454 amoled screen is included on the EVK, enabling developers to design customised GUI’s. The EVK also supports:

  • A g-sensor chip to facilitate user development of scenes
  • Heart rate and motor interface are reserved
  • Bluetooth® audio scene development
  • Nand flash for local music storage


Resources



Part Number Datasheet Dev Kit Hardware Design Guide Reference Design
TLSR921x
TLSR951x
TLSR921x
TLSR951x
B91 Wearable Starter Kit B91 Hardware Design Guideline B91 Wearable Development Board


Demo


Material List


B91 Wearable Starter Kit

  • B91 Wearable Development Board
  • Telink Burning Board / TLSR9 DEV KEY
  • Speaker
  • USB cable
  • Whip Antenna
  • DuPont wire

B91_Wearable_Starter_Kit

PC installed with

Please refer to B91 Wearable EVK V5.0 User Guide for the full information.


B91 Wearable Development Board Top View


B91_Wearable_Development_Board


B91 Wearable Hardware Interface


B91_Wearable_Development_Board_Hardware_Interface


Features


The TLSR9 Wearable solution supports the following features:

  • Bluetooth Classic and Bluetooth LE dual-mode
  • Up to 360*360 Resolution
  • Touch Panel (TP)
  • G-Sensor
  • Heart Rate Sensor
  • iOS ANCS
  • Wechat Lite Protocol
  • HID Service
  • Charging Detect

Quick Start


Supply Power

There are four methods supported to supply power for the EVK.

  • Via Telink Burning Board
  • Via TLSR9 DEV KEY
  • Via USB
  • Via Li Battery

For detailed descriptions, please refer to the “Chapter 2.1: Power Supply” in the B91 Wearable EVK V5.0 User Guide.


Download Firmware

Step 1: Connect to EVK via Telink Burning Board;

Step 2: Download the .bin file according to the introduction of BDT for all Series.

→ Download Via TLSR9 DEV KEY

Step 1: Connect to EVK via TLSR9 DEV KEY;

Step 2: Download the .bin file according to the introduction of BDT for TLSR9 Series.


Test RF Signal

It provides two RF paths on the B91 Development Board:

→ Onboard Antenna

From the 9518 ANT pin to the onboard antenna through the LC matching circuit

→ Whip Antenna

The 9518 ANT pin comes out through the RF PA to the SMA connector, and then connects to the 2.4G whip antenna

For detailed descriptions, please refer to the “Chapter 3: Bluetooth RF path selection” in the B91 Wearable EVK V5.0 User Guide.


Demo Firmware Instruction

Currently there are two demo firmwares for users to implement simple functions after downloading them to EVK:

→ Bluetooth® Audio Demo

Step 1: Download the nosniff.bin to EVK;

Step 2: Re-power on EVK or short press SW1 (reset) to let the chip program run;

Connect with the mobile phone then make calls and play music →

Step 3: Use the phone to connect, turn on the phone’s Bluetooth, scan and find the device with the Bluetooth name “tlk_dev”;

Step 4: Connect the device on the mobile phone;

Step 5: Make calls and play music operations.

Connect with the headset then make a call →

Step 3: Leave the headset in pairing status;

Step 4: Double-click SW4, EVK will start scanning and automatically connect with the headset;

Step 5: Double click SW5, EVK and headset realize the call, single click SW5 to hang up;

Audio_Components


→ AMOLED Screen Display

Step 1: Download the SPI_Demo.bin to EVK;

Step 2: Power on peripheral modules by following the instructions in “Chapter 2.1.1: Via Telink Burning Board Power Supply” of the B91 Wearable EVK V5.0 User Guide;

Step 3: Re-power on EVK or short press SW1 (reset) to let the chip program run;

Step 4: Check the display.

Amoled_Display